-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
The ready-to-fit corner for the knee rail of a yellow GRP handrail. The middle corner clamps round a continuous 50mm corner post at knee rail height and takes the two knee rails at 90°. This version arrives pre-drilled and complete with its M6 nuts and bolts, so there are no rivet nuts to set and no holes to drill on site. Moulded in two halves from glass reinforced plastic, it never rusts and needs no painting. The price shown is for one fitting with its bolts.

Why choose the drilled version
Faster on site. The holes are already drilled and the M6 nuts and bolts come with it, so fitting is a hex key job.
The post stays in one piece. The corner post runs unbroken from base to top rail and the fitting clamps round it.
Square corners without measuring. The two sockets are moulded at a fixed 90°.
No rust, no hot work. GRP does not corrode, needs no painting and goes together cold.
Where it is used
Corners of guard rails round chemical bunds and storage tanks, water and wastewater treatment works, food factories with washdown, coastal and offshore walkways, rail and electrical sites, and machine guarding in factories.
Specifications
| What you get | One two-part middle corner, pre-drilled, with its M6 nuts and bolts |
|---|---|
| Fitting type | Middle corner (4 way, 90°): post through, two knee rails at 90° |
| Suits tube | 50mm outside diameter GRP handrail tube |
| A: post centre to end of each socket | 83mm |
| Overall length | 116mm |
| Fixing holes | 20mm in from the socket ends |
| Fixings | M6 nuts and bolts, included |
| Material | Glass reinforced plastic (GRP), moulded |
| Colour | Safety yellow |
| Weight | 0.65kg |
Load tested system
The 50mm GRP tube handrail system these fittings belong to has been load tested by an independent UK laboratory as a straight two-rail balustrade, 1100mm high with posts at 1000mm centres. It carried 0.4 kN/m, above the 0.36 kN/m general duty load for industrial handrails in BS 4592-0. Keep posts at 1000mm centres or closer to stay within the tested layout.
How many do you need?
One for every corner on a two-rail guard rail, at knee rail height on the corner post. The top of the same post takes a top corner.
| Guard rail shape | Middle corners | Top corners |
|---|---|---|
| L-shape round a tank or machine corner | 1 | 1 |
| U-shape round a bund, pit or bay | 2 | 2 |
| Square enclosure | 4 | 4 |
Building a complete GRP handrail
Everything below suits the same 50mm tube:
- Tube: 5000mm lengths or 3500mm lengths
- Posts: corner post
- Top of posts, drilled: top corner and short tee
- Knee rail on run posts, drilled: mid rail cross
- Feet, drilled: triangular base flange
- Ends: yellow end cap
Buying in volume and happy to drill? The plain middle corner takes M6 rivet nuts. See the whole range in GRP handrail.
Fitting
Set the corner post in its base with the post running unbroken up to the top corner. Cut the knee rails so each fits between the corner post and the next post, cutting square with a fine-tooth saw and wearing a dust mask. Close the two halves of the middle corner round the corner post at knee rail height, push each knee rail fully into its socket, check the rails are level and square, then fit and tighten the M6 bolts supplied. Seal cut tube ends with end caps.
Care
Wash down with water and mild detergent. Check the bolts are tight once a year and after any impact. GRP needs no painting.
Frequently asked questions
Are the bolts included?
Yes. This version comes pre-drilled with its M6 nuts and bolts.
What is the difference from the plain middle corner?
The plain middle corner has no bolts and is fixed with M6 rivet nuts bought separately. This one is drilled and ready to bolt up.
Will it fit steel scaffold tube?
No. It is sized for 50mm outside diameter GRP handrail tube. Steel 48.3mm tube needs key clamp fittings.
Can the corner be other than 90°?
No. For other angles use the adjustable joint or the 120° elbow in the same range.
Is GRP handrail safe near electrical equipment?
GRP does not conduct electricity like steel, which is why it is chosen for rail and electrical sites. Follow your site's own electrical safety rules.
Ordering and delivery
Order online with Express UK Delivery. For a full GRP guard rail, send us a sketch with lengths and corners: call 01744 520 110 or email sales@industrialsuppliesco.co.uk and we will list every tube, fitting and fixing you need.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.









