-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
This square clamp holds a glass panel to the side of a 48.3mm round stainless post, with no channel, no drilling of the glass and no visible fixings on the glass face. It is grade 316 (marine grade) stainless steel with a satin brushed finish, 45 x 45 x 27mm, and comes with rubber pads for 8mm and 10mm glass. Two countersunk screws close the two halves round the glass edge. The price shown is for one clamp, with a minimum order of 8, enough for two panels.

Why use this clamp
Grade 316 for outdoor and coastal rails. 316 stainless contains molybdenum, which resists the chlorides in sea air, pool water and de-icing salt far better than 304. On a seafront balcony, a hotel terrace or round a pool, it keeps its finish with simple cleaning.
Shaped to the post. The back is curved to 48.3mm, the heavier post size used on most commercial and public balustrades, so it sits tight with no rocking and no gap to collect dirt.
Rubber all round the glass. Glass never touches metal. The pads spread the load along the edge and take up small differences in glass thickness, which protects toughened glass from point loads at the clamp.
Small and neat. At 45mm square it is narrower than the post itself, so the rail looks light and the glass does the talking.
Where it is used
Glass balustrades on balconies, terraces, decks, stairs and landings; infill panels in stainless handrails on hotels, restaurants, offices and public buildings; and screens round pools and seating areas.
Specifications
| What you get | One clamp: front and back halves, two closing screws, rubber pads for 8mm and 10mm glass. Minimum order 8 |
|---|---|
| Size | 45 x 45 x 27mm |
| Suits post | 48.3mm round tube (back curved to suit) |
| Glass thickness | 8mm or 10mm |
| Material | Grade 316 stainless steel |
| Finish | Satin brushed |
| Safety pin | None on this clamp |
| Fixing to the post | Not supplied. Usually one M8 stainless screw into a drilled and tapped post |
| Weight | About 0.25 kg |
Which glass clamp to choose
| You need | Clamp |
|---|---|
| Square clamp, 316, 48.3mm post | This clamp |
| Square clamp, 316, 42.4mm post | 316 square clamp for 42.4mm |
| Square clamp, 316, flat post or wall | 316 square clamp, flat back |
| Indoor job, lower cost | 304 square clamp for 48.3mm |
| 12mm glass, or a safety pin | 316 D clamp 63 x 45mm for 48.3mm |
| Black finish | Black square clamp for 48.3mm |
How many do you need?
Most panels are held by four clamps, two on each post, set about 150 to 200mm in from the top and bottom of the glass. A run of three panels between four posts takes 12. A tall or wide panel may need a third clamp each side; follow your glass supplier's or designer's layout.
Choosing the right option
Measure across the post: 48.3mm tube is often sold as 1 1/2" nominal bore. Check the glass is 8mm or 10mm; for 12mm glass use the 316 D clamp 63 x 45mm. Pick 316 for anything outdoors, near the sea or round a pool, and 304 only for dry indoor work. For a full post with clamps already fitted, see the 316 glass balustrade mid post kit for 48.3mm.
Fitting and care
Mark the clamp heights on every post with a level line so the glass sits straight. Drill and tap each post for the fixing screw, fit the back half, then place the rubber pads for your glass thickness. Set the glass on packers, offer up the front half and tighten the two countersunk screws evenly until the glass is gripped firmly, without overtightening. Use toughened safety glass only. Wipe the clamps with warm soapy water and a soft cloth; on the coast, a fresh-water rinse every few weeks keeps the satin finish bright. Do not use wire wool or chloride cleaners.
Frequently asked questions
Is the price for one clamp?
Yes. The price is for one complete clamp with both halves, two screws and the rubber pads. The minimum order is 8, which holds two panels.
Does it need a hole in the glass?
No. This clamp grips the glass edge between rubber pads. There is no safety pin, so the glass needs no hole.
Can I use it on 12mm glass?
No, it takes 8mm or 10mm glass. For 12mm glass use the 316 D clamp 63 x 45mm for 48.3mm posts.
Is the screw that fixes it to the post included?
No. The clamp comes with its two closing screws. The post fixing depends on your post, and most installers use one M8 stainless screw into a tapped hole.
Will it work on a 42.4mm post?
No. The back is curved for 48.3mm and would rock on a smaller tube. Use the 316 square clamp for 42.4mm posts.
Ordering and delivery
Order 8 or more online with Express UK Delivery and same-day dispatch on orders before 2pm, Monday to Friday. For a full balustrade, call 01744 520 110 or email sales@industrialsuppliesco.co.uk and we will check quantities and delivery before you order.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Minimum order 8 pcs




