-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
This 316 stainless square clamp holds a glass panel to a square post, box section or wall, in a satin brushed finish made for outdoor and seaside balustrades. It measures 45 x 45 x 27mm, has a flat back and comes with rubber pads for 8mm and 10mm glass. Two countersunk screws close the two halves round the glass edge, so the glass needs no holes. The price shown is for one clamp, with a minimum order of 8, enough for two panels.

Why use this clamp
316 for outdoors. Grade 316 stainless steel resists rust and tea staining far better than 304, so it is the right choice for balconies, terraces, pool surrounds and anywhere near the sea or road salt.
Flat back for square posts and walls. Square and rectangular posts, box section, flat bar and walls need a flat-back clamp. A curved-back clamp would rock and never hold the glass straight.
Slotted fixing hole. The back half has a 14 x 10mm slotted hole for the post screw, which gives a little room to line the clamps up before you tighten.
Rubber all round the glass. Glass never touches metal. The pads spread the load along the edge and take up small differences in glass thickness. The glass sits 16mm deep in the slot.
Where it is used
Glass balustrades on balconies, roof terraces, decks and stairs with square stainless posts; glass infill in stainless box-section frames; glass screens fixed to walls; and pool fences and windbreaks where the fittings face the weather all year.
Specifications
| What you get | One clamp: front and back halves, two countersunk closing screws, rubber pads for 8mm and 10mm glass. Minimum order 8 |
|---|---|
| Size | 45 x 45 x 27mm |
| Suits | Flat post, box section or wall (flat back) |
| Glass thickness | 8mm or 10mm |
| Glass in the slot | 16mm deep |
| Closing screws | Two, at 24.5mm centres, 10mm in from the post side |
| Fixing to the post | 14 x 10mm slotted hole in the back half. Post screw not supplied; usually one M8 screw into a drilled and tapped post |
| Material | Grade 316 stainless steel |
| Finish | Satin brushed |
| Safety pin | None on this clamp |
| Weight | About 0.20 kg |
Which square glass clamp to choose
| You need | Clamp |
|---|---|
| 316 square clamp, flat post | This clamp |
| 316 square clamp, 42.4mm round post | 316 square clamp for 42.4mm |
| 316 square clamp, 48.3mm round post | 316 square clamp for 48.3mm |
| Indoor use, flat post | 304 square clamp, flat back |
| Black finish, flat post | Black square clamp, flat back |
| 12mm glass, flat post | 316 square clamp 52 x 52mm, flat back |
| D shape, flat post, up to 12mm glass | 316 D clamp 63 x 45mm, flat back |
How many do you need?
Most panels are held by four clamps, two on each post, set about 150 to 200mm in from the top and bottom of the glass. A run of three panels between four posts takes 12. A tall or wide panel may need a third clamp each side; follow your glass supplier's or designer's layout.
Choosing the right option
Use this flat-back clamp on any face at least 45mm wide. Check the glass is 8mm or 10mm; for 12mm glass use the 52 x 52mm square clamp or the D clamp. If your posts are round, choose the clamp curved for 42.4mm or 48.3mm tube. Indoors, the 304 clamp does the same job for less.
Fitting and care
Mark the clamp heights on every post with a level line. Drill and tap the post, fix the back half through its slotted hole, line it up and tighten, then fit the rubber pads for your glass. Set the glass on packers, offer up the front half and tighten the two screws evenly until the glass is gripped firmly, without overtightening. Use toughened safety glass only. Outdoors, rinse the clamps with fresh water and wipe along the grain every few weeks, more often near the sea or a pool. Use warm soapy water; avoid chlorine bleach, wire wool and scouring pads.
Frequently asked questions
Is the price for one clamp?
Yes. The price is for one complete clamp with both halves, two screws and the rubber pads. The minimum order is 8, which holds two panels.
Does it need a hole in the glass?
No. This clamp grips the glass edge between rubber pads. There is no safety pin, so the glass needs no hole.
Can I use it on 12mm glass?
No, it takes 8mm or 10mm glass. For 12mm glass use the 316 square clamp 52 x 52mm or the 316 D clamp 63 x 45mm.
Will it fit a round post?
No, the back is flat. Choose the 316 square clamp curved for 42.4mm or 48.3mm tube.
Ordering and delivery
Order 8 or more online with Express UK Delivery and same-day dispatch on orders before 2pm, Monday to Friday. For a full balustrade, call 01744 520 110 or email sales@industrialsuppliesco.co.uk and we will check quantities and delivery before you order.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Minimum order 8 pcs






