-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
The Sheffield cycle stand is the plain inverted-U hoop you see outside offices, schools, stations and shops across the UK, and it has been recommended by cycling groups since its introduction in the 1990s. This version is bent from 48mm diameter steel tube, stands 750mm above ground and runs 800mm long, so one stand gives secure parking for two bicycles, one on each side. You choose the finish (galvanised, galvanised and black, or stainless steel) and the fixing (cast in for new paving and tarmac, or bolt down for existing concrete). Facilities managers, groundworkers and schools choose it because it is simple to install and has nothing to wear out.
Why the Sheffield stand works
Two points of contact for the lock
Because the hoop is long and low, a rider leans the bike along the rail and locks the frame and a wheel together. A stand that only grips the front wheel lets thieves take everything but the wheel; a Sheffield stand holds the frame itself.
Tube and finish built for outdoor life
The 48mm tube is a substantial section that is comfortable to lean a bike against. The galvanised version is hot-dip galvanised, which protects the steel inside and out. The black version is galvanised first and then powder coated black, so if the coating is chipped by a pedal or lock the zinc underneath still stops rust. The stainless version needs no coating at all and keeps its satin look in town centres and coastal air.
Nothing to break
There are no moving parts, no locks to seize and no plastic to perish. Once it is in, maintenance is an occasional wash.
Where it's used
Office forecourts, school and college entrances, supermarket and retail frontages, high streets and public squares, hospitals, stations, leisure centres, new housing with planning-condition cycle parking, and staff car parks. Stands are usually set in rows to form a cycle parking bay, on open paving or under a shelter.
Specifications
| Design | Sheffield (inverted U) cycle stand |
|---|---|
| Tube diameter | 48mm |
| Tube wall thickness | Not published for this line |
| Height above ground | 750mm |
| Length | 800mm |
| Bikes per stand | 2 (one each side) |
| Finishes | Hot-dip galvanised; galvanised and black powder coat; stainless steel |
| Cast in fixing | Legs set 300mm below ground in concrete, ragged ends for anchorage |
| Bolt down fixing | Round flange plate on each leg: 133mm x 5mm (galvanised and black), 120mm x 5mm (stainless) |
| Bolts required | 6 per stand (3 per plate), not included; bolt size not published |
| Weight | Galvanised and black: 9kg cast in, 8kg bolt down. Stainless: 9kg cast in, 7kg bolt down |
| Stainless grade | Made in grade 304 and grade 316; please state your required grade when ordering |
| Guarantee | 12 months if installed and used correctly |
Choosing the right option
Finish. Galvanised is the most economical and the standard for schools, workplaces and car parks where a hard-wearing, utilitarian look is fine. Galvanised and black suits town centres, conservation areas and modern frontages where the stand should look tidy against dark street furniture, and the galvanised layer underneath protects any chips. Stainless steel is the choice for prestige entrances, coastal sites and anywhere a bright, coating-free finish is wanted for the long term.
Fixing. Choose cast in when the surface is being laid or relaid, such as new block paving, slabs or tarmac: the legs go 300mm into concrete and the surface is dressed around them, leaving no plates or bolt heads. Choose bolt down when you are adding parking to sound existing concrete: no excavation is needed, just drilling for six bolts per stand.
Spacing. The manufacturer does not publish a recommended spacing between stands, so follow your local authority's cycle parking guidance or your project designer's layout.
Installation, use and care
Cast in: excavate a suitable hole for each leg, stand the hoop upright and level, and set the legs 300mm deep in concrete before laying the finished surface around them. Bolt down: place the stand on a suitable concrete surface, mark and drill through the three holes in each plate, and fix with six anchors of your choice (not supplied). Wash with water and mild detergent; touch up any deep damage to the black coating.
Frequently asked questions
How many bikes does one stand hold?
Two. A bike parks along each side of the hoop and can be locked by frame and wheel. For larger numbers, install stands in a row.
Are fixings included with the bolt-down version?
No. Each bolt-down stand needs six bolts, three through each base plate, which you supply to suit your concrete. The bolt size is not published for this line.
Can I fit the cast-in version into existing paving?
Yes, but you will need to lift the paving, set each leg 300mm deep in concrete and relay around it. On sound concrete, bolt down is quicker.
Which stainless grade is it?
The stand is manufactured in grade 304 and grade 316. Grade 316 is normally specified near the sea. Tell us which grade your project needs when you order and we will confirm.
Ordering and delivery
Select your finish and fixing above and add the quantity you need; all prices include VAT. For bulk orders, mixed finishes, project quotes or delivery questions, call 01744 520110 or email sales@industrialsuppliesco.co.uk and our team will help you plan the cycle parking bay.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.







