-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
If you are adding cycle parking to an office, school, shop front or residential block, this rounded hoop cycle stand gives every bike two solid points to lock against without taking over the pavement. It is a single 48mm steel tube rolled into a full semicircular arch, standing 770mm high and 750mm wide, so it reads as a softer, more architectural shape than a square-topped Sheffield stand while doing exactly the same job. One stand parks two bicycles, one on each side, using the riders' own D-locks or cable locks. Choose a galvanised, galvanised and black, or Grade 304 stainless steel finish, then pick cast in for new paving or bolt down for an existing slab.
Why it works
A continuous tube with no joints in the arch
The hoop is formed from one length of 48mm diameter tube, so there is no welded joint across the top for a thief to attack and no corner where a frame can slip off. The round section is kind to paintwork and lets a rider pass a D-lock around both the frame and a wheel.
Two-sided parking in a small footprint
At 750mm across, the stand supports a bike along its frame on each face. A row of stands keeps bikes off railings, trees and drainpipes.
Finishes matched to the site
Galvanised mild steel is the hard-wearing, low-maintenance option for most commercial sites. The galvanised and black version adds a black coated finish over the galvanising for conservation areas and smart frontages. Grade 304 stainless steel keeps a bright brushed look outside offices, hospitals and new-build schemes.
- Single 48mm tube rolled into a semicircular hoop
- 770mm high x 750mm long above ground
- Parks two bikes per stand
- Cast in (300mm below ground) or bolt down on 133mm round plates
- UK manufactured, 12-month guarantee when installed and used correctly
Where it's used
Typical installations include office and business-park entrances, primary and secondary schools, colleges, retail parks and high-street shop fronts, GP surgeries and hospitals, railway and bus interchanges, leisure centres and apartment courtyards. Planning conditions and travel plans often call for "Sheffield-type" stands; this rounded variant gives the same two-point support with a gentler profile that suits landscaped schemes.
Specifications
| Product | Rounded hoop cycle stand (semicircular variant of the Sheffield stand) |
|---|---|
| Height above ground | 770mm |
| Length (overall width) | 750mm |
| Tube | 48mm diameter; wall thickness not published for this line |
| Capacity | 2 bicycles (one each side) |
| Finishes | Galvanised mild steel; Galvanised & Black; Stainless Steel Grade 304 |
| Cast in | Ragged legs, set 300mm below ground in concrete |
| Bolt down | Round flange plate 133mm x 5mm on each leg; 6 bolts per stand (3 per plate), fixings not included |
| Weight | 9kg cast in; 8kg bolt down |
| Guarantee | 12 months if installed and used correctly |
| Manufactured in | United Kingdom |
Choosing the right option
Finish. Galvanised is the workhorse: it is the lowest-cost choice and needs no painting, though it weathers from bright silver to a dull grey. Galvanised & Black keeps the galvanised protection underneath and gives a black finish that sits well against brick, railings and heritage street furniture; expect occasional touch-up where locks rub. Stainless Steel Grade 304 costs the most but stays bright with a wipe-down and suits glazed entrances and prestige frontages. For sites close to the sea or near de-icing salt spray, ask us before ordering.
Fixing. Choose Cast In when you are laying new paving or can break out the surface: the legs are concreted 300mm into the ground and nothing is left at surface level to trip on or tamper with. Choose Bolt Down for an existing sound concrete slab where excavation is not practical; each leg has a 133mm round plate taking three anchors. Bolt-down stands can be lifted and relocated later, while cast-in stands are effectively permanent.
Installation, use & care
For cast-in stands, excavate a hole for each leg, stand the hoop upright on the correct centres, check it is plumb and pour concrete to 300mm depth, propping it until the concrete has cured. Bolt-down stands must go onto a suitable concrete surface using six anchors suited to the slab (not supplied). Leave enough clearance for a bike either side and between stands in a row. Wash stainless steel periodically with clean water and check bolt-down fixings during routine maintenance.
FAQs
How many bikes does one stand hold?
Two: one parked against each face of the hoop. Riders lock the frame to the tube with their own lock.
How is this different from a Sheffield stand?
It does the same job and has the same two-point support, but the top is a rolled semicircle rather than a flat top rail with two bends.
Are the bolts included with the bolt-down version?
No. Each stand needs six bolts, three per base plate. Choose anchors to suit your concrete; we can advise on suitable resin or sleeve anchors.
Can I get other colours?
This listing covers galvanised, galvanised and black, and stainless steel. Call us if your scheme needs another finish and we will check availability for you.
Ordering & delivery
Order online for UK delivery, or contact our team on 01744 520110 or sales@industrialsuppliesco.co.uk for quantity pricing, project quotes and lead times on larger runs. Please check the finish and fixing type before ordering, as each combination is supplied ready for that installation method.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.







