Google Top Quality Store — Verified Exceptional Shopping Experience

Heavy Duty Rubber D Fender - Arched Dock & Wall Buffer Strip for Lorries, Forklifts & Quays, 150 x 152 x 2000mm


Price:
Sale price£477.40
Inc. Vat

Express UK Delivery (2 Working Days)

In stock, ready to ship

Trusted by Industry Professionals

Description

Where lorries, telehandlers and loaded forklifts hit a dock face or wall hard and often, a thin buffer strip wears through quickly. This heavy duty rubber D fender is a near-solid 150mm wide, 152mm high section of black SBR rubber, 2 metres long and about 58kg per length. It has a flat base, an arched top and a small arched core running the full length. It is built for distribution centres, ports, wash bays and yards where the knocks are heavy and frequent, and it gives site managers, facilities teams and groundworks contractors a tough fender to fix along an edge and leave in service for years.

Why it works

Mass where the impact lands

Most of this profile is solid rubber. The base wall under the core is 46mm thick and the arched crown is thicker still, so a heavy strike is met by a deep body of rubber rather than a thin skin. That mass absorbs energy and spreads it along the length before it reaches the concrete or steel behind.

A small core for controlled give

The arched core is only 60mm high and sits low in the section. It lets the fender compress slightly under a hard hit and recover its shape afterwards, without the soft, collapsible feel of a thin-walled hollow strip. The result is a firmer buffer suited to heavier vehicles and plant.

Flat base, rounded face

The 150mm flat base sits square on a dock face, wall or kerb line, and the rounded top turns glancing blows aside instead of catching a tyre, fork tip or trailer corner. SBR rubber resists scuffing, does not crack like plastic and keeps working outdoors in wet yards.

  • Near-solid 150 x 152mm section for heavy impacts
  • Small arched core gives controlled compression and recovery
  • Flat 150mm base sits square on concrete or steel
  • Rounded crown deflects glancing blows from wheels and forks
  • 2 metre lengths that butt together for long runs

Where it's used

Typical installations include the front face of raised loading docks, quay and jetty walls, vehicle wash bay walls, the base of warehouse walls along busy forklift routes, the ends of racking runs and around building columns in yards. Laid base-down on the floor, it also works as a heavy wall protection kerb that keeps wheels away from cladding, doors and plant room walls.

Specifications

Width 150mm
Height 152mm
Length 2000mm (one length per unit)
Weight Approx. 58kg per length
Material SBR rubber, black
Profile Arched D-section, flat base, straight sides, rounded top
Core Arched, 60mm high, running the full length
Base wall 46mm below the core
Hardness and temperature range Not published for this line
Fixings Not included, fender only

Dimensions are typical. Extruded rubber varies slightly from batch to batch, so if an exact size matters for your job, call us before ordering and we will measure current stock.

Technical drawing of the 150 x 152 x 2000mm rubber D fender with cross-section dimensions

Choosing the right option

Measure the edge you need to protect and divide by two to get the number of lengths, rounding up. A single dock door usually takes one or two lengths along the dock face; a wall or quay needs one length for every 2 metres of run. Lengths butt end to end for a continuous line and can be trimmed on site.

Pick this size where lorries, plant or loaded forklifts make contact. For lighter traffic such as pallet trucks and cages, a smaller hollow D fender strip is lighter to handle and fix. At the exact points where a trailer backs onto a dock, moulded dock bumpers take the concentrated load, and many sites fit both: bumpers either side of the door and this fender along the rest of the face.

Installation, use and care

At around 58kg a length, plan for two people or a lifting aid. Fix the flat base to sound concrete, masonry or steel with heavy anchors suited to the surface, using large washers or a flat bar inside the core to spread the clamping load. Drill an access hole through the crown above each fixing so a socket reaches the bolt, and space fixings evenly with one close to each end. Cut with a fine-toothed saw, wetted to ease the cut. Check fixings on busy runs and clean with water and mild detergent.

FAQ

Is the price for one length?
Yes. The price is for one 2 metre length weighing about 58kg. Add the number of lengths you need to your basket.

Are fixings supplied?
No, the fender is supplied on its own. Choose anchors to suit your concrete, blockwork or steel.

Can it be cut to length?
Yes. A fine-toothed saw cuts it cleanly, so you can trim lengths to suit doorways, corners and the end of a run.

Will it stop a reversing lorry?
No. It cushions impacts and protects the surface behind it, but it is not a vehicle restraint. Use wheel stops, kerbs or barriers where a vehicle must be physically halted.

Ordering and delivery

Order online for express UK delivery, with same-day dispatch on orders placed before 2pm, Monday to Friday. Each length is heavy, so make sure someone is on hand to unload. For larger runs or a size check against current stock, call us on 01744 520 110 or email sales@industrialsuppliesco.co.uk.

Our products have been used by

Logos are for illustrative purposes only and do not imply official endorsement

About Us

Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments

Payment & Security

American Express Apple Pay Diners Club Discover Google Pay Klarna Maestro Mastercard Shop Pay Union Pay Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Heavy Duty Rubber D Fender - Arched Dock & Wall Buffer Strip for Lorries, Forklifts & Quays, 150 x 152 x 2000mm

£477.40 Inc. Vat

You may also like

Recently viewed