-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
Where there is no room for a full bench but people still need to pause, a perch bench does the job. This 1000mm leaning seat puts a seven-slat steel seat at 700mm, roughly hip height for most adults, so users rest their weight against it rather than sitting down. It is aimed at councils, transport operators, hospital estates and contractors fitting out bus stops, platforms and busy pavements. The frame comes fully welded on two round posts with bolt-down base plates, in plain galvanised steel, galvanised steel with one of seven RAL powder-coat colours, or brushed grade 304 stainless steel.
Why it works
A seat shaped for leaning
The seat is built from seven square-section steel slats. Five run flat across the top, and the outer slat on each long edge is angled downwards. Those angled edges take the hard corner off the front of the seat where it meets the back of your thighs. Both long sides are identical, so it can be used from either direction. Every slat end is closed with a plastic end cap.
A small footprint
Two 48mm round legs on the centreline carry the whole seat, so the only ground contact is a pair of 133mm round flange plates. The floor stays clear for sweeping, and the perch fits narrow pavements where a bench with a backrest would block the route.
All-steel construction
There are no timber or composite slats to split, rot or be prised off. At 24kg it is easy for two people to position, and once bolted down with six 12mm fixings it is a permanent piece of street furniture.
- 1000mm long, 450mm wide, 700mm high
- Seven slats with angled outer edges, usable from both sides
- Twin 48mm legs on 133mm x 5mm round flange plates
- Supplied fully welded; bolts down with 6 x 12mm bolts
- Galvanised, galvanised plus RAL powder coat, or 304 stainless
Where it's used
Bus stops and the inside of bus shelters, railway and tram platforms, hospital and clinic entrances, shopping streets and market places, covered walkways and canopies, smoking shelters, and staff break areas on industrial and business parks. Wherever people wait a few minutes and floor space is tight, a perch gives somewhere to rest without the footprint of a sitting bench.
Specifications
| Product type | Perch bench / leaning seat, bolt down |
|---|---|
| Length | 1000mm |
| Width | 450mm |
| Height | 700mm |
| Seat | 7 square-section steel slats (5 flat, 2 angled outer slats) with plastic end caps |
| Legs | 2 x 48mm diameter round legs |
| Base plates | Round flange plate, 133mm x 5mm, one per leg |
| Fixing | Bolt down only, 6 x 12mm bolts per bench (bolts not included) |
| Material | Galvanised mild steel, or grade 304 stainless steel |
| Finish options | Galvanised; galvanised + powder coat in RAL 1021, 3020, 5017, 6005, 7001, 9005 or 9010; brushed stainless steel |
| Weight | 24kg |
| Supplied | Fully welded |
| Number of users | Not published for this line |
| Slat section size | Not published for this line |
| Guarantee | 12 months when installed and used correctly |
Choosing the right option
Plain galvanised is the most economical choice and the hardest-wearing for exposed, high-footfall sites. The powder-coated versions add a RAL colour over the galvanising. Jet black RAL 9005, moss green RAL 6005 and silver grey RAL 7001 sit quietly in parks, conservation areas and alongside existing street furniture. Traffic red RAL 3020, traffic blue RAL 5017, colza yellow RAL 1021 and pure white RAL 9010 stand out clearly against paving and can match a transport or corporate colour scheme. Brushed 304 stainless suits civic plazas and modern interchanges where no coating is wanted. For seafront or heavily salted sites, talk to us about finish choice before you order.
Installation, use & care
The perch arrives fully welded, so there is nothing to assemble. Set out the two base plates on a sound concrete base, then drill and fix with six 12mm bolts or anchors suited to the substrate, three per plate; fixings are not supplied. Check the seat is level before final tightening. Galvanised and coated finishes need only an occasional wash with mild detergent; touch in any chips to powder coat promptly. Clean stainless steel along the grain of the brushed finish.
Frequently asked questions
How many people can use it at once?
A user rating is not published for this line, so plan with its 1000mm seat length. For more capacity, install several perches in a row with a clear walking gap between them.
Can it be concreted in instead of bolted down?
No. This model is bolt down only. Each leg sits on a 133mm round flange plate, and the bench needs six 12mm bolts into a suitable concrete surface.
Can I have a RAL colour that is not listed?
The galvanised frame can be powder coated in other BS or RAL colours. Call or email us with the exact colour code for a price.
Is a perch a substitute for ordinary seating?
No. A perch is designed for short rests by people who are able to stand. It works best alongside conventional seats with backs and arms, which some users will still need.
Ordering & delivery
Choose your finish above and add to basket, or call 01744 520110 or email sales@industrialsuppliesco.co.uk for quantity pricing, special colours or a formal quote. Prices shown include VAT. The perch is delivered fully welded to UK mainland addresses; contact us for current lead times and offshore delivery.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.










