-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
If you are specifying street furniture for a conservation area, a market square or a pedestrianised high street, a plain yellow post rarely gets past the planning officer. This ornamental bollard gives you a traditional profile on a practical steel post: a straight 114mm tube standing 900mm above ground, finished with a low domed cap, a collar ring just below it and a second pair of rings at mid-height. It is made in Britain from mild steel, hot-dip galvanised, and offered plain or powder coated in seven standard RAL colours. You choose concrete in, bolt down or removable fixing to suit the ground and how you manage access.
Why it works
Galvanised mild steel, not a painted shell
The body is a 114mm mild steel tube with a 3mm wall. The cap and rings are welded on, not clipped or glued, so there is nothing loose for vandals to prise off. The whole bollard is hot-dip galvanised, so the zinc coating covers the inside and outside of the tube. If a coloured finish chips on a busy kerb line, the steel underneath stays protected.
A design that reads as traditional
Two pairs of raised rings and a rimmed, gently domed cap break up the plain tube. The bollard looks at home next to cast iron railings, York stone paving and period shopfronts, without the cost or weight of a solid cast iron bollard. The top pair of rings sits at the cap, and the second pair sits roughly halfway down the post. The rings are 30mm apart within each pair and the pairs are 420mm apart, so a run of bollards lines up neatly.
Three ways to fix it
The same post is available cast into concrete, bolted to an existing slab, or set in a lift-out ground socket. You can therefore use one design across a whole scheme, even where some positions need occasional vehicle access.
- 900mm above finished ground level, 114mm diameter, 3mm wall
- Welded cap and rings, hot-dip galvanised throughout
- Plain galvanised or galvanised and powder coated in RAL 9005, 1021, 3020, 5017, 6005, 7001 or 9010
- Concrete in, bolt down or removable
Where it's used
Typical sites include town centre pedestrian zones, conservation-area streets, market squares, church and civic forecourts, school entrances, park gates, seafront promenades and retail precincts. It keeps vehicles off footways and verges and marks the edge of a shared space. It also protects shopfronts and planters from overrunning traffic. It is a decorative traffic-management bollard; no crash or impact rating is published.
Specifications
| Height above ground | 900mm |
|---|---|
| Tube diameter | 114mm (114.3mm on the manufacturer's drawing) |
| Wall thickness | 3mm |
| Material | Mild steel tube, cap and rings welded on |
| Finish | Hot-dip galvanised; or galvanised and powder coated |
| Colours | Plain galvanised, Jet Black RAL 9005, Colza Yellow RAL 1021, Traffic Red RAL 3020, Traffic Blue RAL 5017, Moss Green RAL 6005, Silver Grey RAL 7001, Pure White RAL 9010 |
| Ring layout | Cap and first ring 30mm pitch; 420mm to second pair; second pair 30mm pitch |
| Concrete in | 300mm below ground, welded fixing spikes |
| Bolt down | Round base plate for a suitable concrete surface; plate size and bolt size not published for this line; fixing bolts not included |
| Removable | Ground socket 300mm below ground with welded fixing spikes; padlock not included |
| Weight | 13kg (concrete in and bolt down); removable 21kg total, 13kg lift weight |
| Impact rating | Not published for this line |
| Guarantee | 12 months from the manufacturer when installed and used correctly |
Choosing the right option
Fixing. Choose concrete in for new paving schemes and permanent positions. It is the cheapest and strongest choice, and nothing shows at ground level. Bolt down suits existing concrete slabs where you cannot dig, but the round base plate stays visible and you need to supply suitable anchors. Removable is for gateways, market pitches and emergency or delivery routes. The post lifts out of a socket set flush in the paving, and the socket's hinged lid can then be closed. Allow for a padlock. The post itself weighs 13kg to lift.
Colour. In conservation areas, black RAL 9005 is the usual choice because it matches cast iron railings and lamp columns. Moss green RAL 6005 is common in parks. Plain galvanised suits stone and granite schemes and needs no repainting. Check your local authority's street design guide or conservation officer before ordering. The contrasting colours, such as yellow, white, blue and red, help partially sighted pedestrians see the bollard in shared spaces.
Installation, use and care
For concrete in and removable posts, dig a hole deep enough for the 300mm below-ground section plus a concrete surround. Set the post or socket plumb and check that the 900mm height is measured from finished ground level, then let the concrete cure. Removable sockets must sit flush so the lid closes properly. Bolt-down posts need a sound concrete base and anchors chosen for it. Galvanised posts need no maintenance. On coated posts, touch in chips with matching RAL paint. Clear grit and leaves from removable sockets regularly.
Frequently asked questions
Is the bollard cast iron?
No. It is a mild steel tube with welded steel rings and cap, hot-dip galvanised. It gives a traditional look at a fraction of the weight of cast iron, so it is easier to handle and install.
Are fixing bolts or a padlock included?
No. Bolt-down posts are supplied without anchors because the right fixing depends on your concrete. Removable posts are supplied without a padlock. We can advise on both when you order.
Can I have a colour that is not listed?
The listing covers seven standard RAL colours and plain galvanised. For another RAL shade, or for eyelets and chains between posts, call us for a quote before ordering.
Is this bollard crash rated?
No impact rating is published. It is designed to guide and deter vehicles in pedestrian areas, not to stop a deliberate impact.
Ordering and delivery
Choose your fixing method and finish above. Prices include VAT. For multi-post orders, scheme quantities or help matching an existing run of bollards, call 01744 520110 or email sales@industrialsuppliesco.co.uk. Delivery is to UK mainland addresses, and we will confirm the lead time when you order.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

























