-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
If you are specifying bollards for a market square, a conservation-area street or the approach to a listed building, a plain steel post can look out of place. This ornamental bollard gives you a traditional profile on a slim 76mm steel tube: a domed cap, a collar ring directly beneath it and a second collar ring a little below mid-height. It stands 1000mm above ground and comes in three fixing types and eight finishes, so one design can carry through a whole scheme. That covers cast-in runs along a footway, bolt-down posts on an existing slab, and removable posts where vehicles need occasional access.
Why it works
Galvanised steel underneath every finish
The tube is mild steel with a 3mm wall. The cap and both rings are welded on, so there are no loose castings to work free. Every bollard is hot-dip galvanised. On the coloured versions the powder coat is applied over the galvanising, so if the paint gets chipped, the zinc layer underneath still protects the steel.
Traditional look, modest footprint
At 76mm diameter the post is slender enough to sit on a narrow pavement without crowding pedestrians, and the dome-and-collar profile gives it the period look that town-centre and heritage schemes call for. It is a pedestrian-zone and street-furniture bollard. It is not a crash-rated or anti-ram bollard, so do not specify it to stop deliberate vehicle impact.
- 1000mm above ground, 76mm diameter, 3mm wall
- Domed cap with two welded collar rings
- Galvanised, or galvanised and powder coated in seven RAL colours
- Concrete in, bolt down or removable
Where it's used
Typical sites are high streets and pedestrianised precincts, conservation areas, civic squares, churchyards and park entrances. You will also see them on promenades and harbour walks, at school frontages and in shared-surface schemes, where they mark the line between footway and carriageway or keep vehicles off paving and verges.
Specifications
| Height above ground | 1000mm |
|---|---|
| Tube diameter | 76mm |
| Wall thickness | 3mm |
| Material | Mild steel tube; cap and collar rings welded on |
| Finish | Hot-dip galvanised, or galvanised and powder coated: Jet Black RAL 9005, Colza Yellow RAL 1021, Traffic Red RAL 3020, Traffic Blue RAL 5017, Moss Green RAL 6005, Silver Grey RAL 7001, Pure White RAL 9010 |
| Concrete in | 400mm below ground, welded fixing spikes |
| Bolt down | Round base plate; plate size and hole pattern not published for this line; fixing bolts not included |
| Removable | Ground socket 220mm below ground with welded fixing spikes; padlock not included |
| Weight | 13kg (concrete in and bolt down); removable 13kg lift weight, 21kg total |
| Guarantee | 12 months manufacturer's guarantee when installed and used correctly |
| Origin | Made in Britain |
Choosing the right option
Fixing. Choose concrete in for new paving or wherever you can excavate. It gives the cleanest finish, with the post rising straight out of the surface. Choose bolt down when you are fixing to an existing concrete slab and cannot dig, but allow for anchors suited to your base, as bolts are not supplied. Choose removable for access routes, market days and maintenance lanes. The post lifts out of a socket that sits flush with the paving and locks with a padlock, which you supply.
Colour. In most conservation areas Jet Black is the default and the easiest to get approved. Moss Green suits parks and village greens, and Silver Grey or Pure White sit well against pale stone and on seafronts. Plain galvanised is the lowest-cost option for a working, utilitarian look. Yellow, red and blue are useful where the post must stand out, for example at a school gate. Check with your planning or highways officer before ordering for a listed setting.
Installation, use and care
For concrete-in and removable bollards, dig a suitable hole, set the post or socket plumb with the welded spikes bedded in concrete, and leave it to cure before loading. For removable posts, set the socket rim level with the finished paving. Bolt-down posts need a sound concrete surface and anchors chosen to suit it. Wash coloured posts down occasionally and touch in any chips promptly. Galvanised posts need no routine maintenance.
FAQ
Is the bollard galvanised under the paint?
Yes. Every finish starts as a hot-dip galvanised post, and the coloured versions are powder coated over the galvanising.
Are fixing bolts or a padlock included?
No. Bolt-down posts are supplied without anchors and removable posts without a padlock, so order both to suit your site.
Can I mix fixing types along one run?
Yes. All three versions share the same 1000mm above-ground profile, so a removable post in a line of concrete-in posts matches the others.
Is it suitable for stopping vehicles at speed?
No. It is a street-furniture and demarcation bollard, not an impact-tested security product.
Can I order a colour that isn't listed?
Other RAL colours may be possible. Call or email us with the RAL number before ordering.
Ordering and delivery
Prices include VAT. For quantities, a matched scheme with other ornamental designs, or delivery to site, contact our trade team on 01744 520110 or sales@industrialsuppliesco.co.uk. If you have a programme to meet, ask about lead times on coloured finishes when you order.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

























