-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
If you need a traditional street bollard with real weight behind it, this is a strong choice. The post is 168mm in diameter with a 5mm wall and stands 1000mm above ground. It has a low, gently crowned cap and two half-round rings welded close together just below the top. The body below the rings is plain and straight, so the post reads as heritage street furniture without fussy detail. It suits town-centre schemes, conservation-area footways, retail precincts and civic squares where the bollard has to look right and take knocks from vans, trolleys and delivery traffic. You choose the fixing (concrete in, bolt down or removable) and the finish: plain hot-dip galvanised or galvanised with one of seven RAL colours.
Why it works
A heavier section than most ornamental posts
Many decorative bollards are built on 76mm or 114mm tube. This one uses 168.3mm tube with a 5mm wall, so it has more steel at the point of impact. On a busy pedestrian street that means fewer bent posts after a careless reversing manoeuvre, and longer periods between replacements.
Simple, recognisable heritage detailing
The cap and both rings are welded to the tube, so there are no loose castings to work free or rattle. With both rings bunched at the head, the post has a clean silhouette that sits comfortably beside cast-iron railings, stone kerbs and York stone paving.
Galvanised first, then coloured
Every post is hot-dip galvanised. Coloured versions are galvanised and then coated, so a chip in the paint exposes zinc rather than bare steel. That matters on salted winter footways and on the coast.
- 168.3mm x 5mm mild steel tube, 1000mm above ground
- Low crowned cap and two welded rings at the head
- Concrete in, bolt down or removable with a ground socket
- Plain galvanised or galvanised plus RAL colour
Where it's used
Typical sites are pedestrianised high streets, market squares, conservation-area footways, school and college frontages, hospital and civic building entrances, seafront promenades, park gateways and retail forecourts. Removable posts are the usual choice where emergency vehicles, market traders or maintenance crews need occasional access through a line of bollards.
Specifications
| Height above ground | 1000mm |
|---|---|
| Tube diameter | 168.3mm (168mm nominal) |
| Wall thickness | 5mm |
| Material | Mild steel tube; cap and two rings welded on |
| Ring positions | First ring 55mm below the top, second ring 55mm below the first |
| Concrete in | 500mm below ground, with welded fixing spikes |
| Bolt down | Square base plate for fixing to a suitable concrete surface; plate size and bolt pattern not published for this line |
| Removable | Ground socket 300mm below ground, with welded fixing spikes |
| Finish | Hot-dip galvanised, or galvanised and coated in RAL 9005, 1021, 3020, 5017, 6005, 7001 or 9010 |
| Weight | 32kg (removable: 32kg lift weight, 45kg including socket) |
| Not included | Fixing-down bolts and padlock |
| Guarantee | 12 months from the manufacturer, if installed and used correctly |
Choosing the right option
Fixing. Concrete in is the strongest and most tamper-resistant fixing. Use it for permanent lines where you can excavate. Bolt down suits existing slabs, podium decks or locations where you cannot dig. The bolts must suit the concrete, and the substrate has to be sound enough to hold them. Removable posts lift out of a flush ground socket and are secured with a padlock (not supplied), so you can open a route without leaving a trip hazard.
Colour. In conservation areas the local authority often specifies the colour, typically Jet Black RAL 9005 or Moss Green RAL 6005 to match railings and lamp columns. Check your planning or highways specification before ordering. Plain galvanised needs no maintenance and suits modern schemes. Traffic Red, Traffic Blue and Colza Yellow are used where the post should stand out, for example in a school's corporate colours or at a hazard. Silver Grey and Pure White suit contemporary paving and stonework.
Installation, use and care
For concrete-in posts, excavate a hole deep enough for the 500mm below-ground section plus a concrete bed. Set the post plumb and haunch it in concrete so the welded spikes are fully embedded. Removable sockets are installed the same way, finishing flush with the paving. Bolt-down posts need sound concrete and fixings rated for that base. Wash coated posts occasionally and touch in any chips to keep the colour even. Galvanised posts need no routine treatment.
FAQ
Is this a crash-rated security bollard?
No. It is a heavy-duty ornamental bollard for pedestrian protection and access control. It is not an impact-tested anti-terrorism product. For vehicle-mitigation ratings you need a certified system.
Are fixing bolts and a padlock included?
No. Bolt-down posts need fixings chosen to suit your concrete. Removable posts need a padlock of your choice.
Can I order a colour not listed?
The listed RAL colours are available here. For any other RAL shade, call us before ordering and we'll check availability and price.
Can chains be added between posts?
The manufacturer offers eyelets, hooks and chains for this range. Call us for a quote; they are not included in these prices.
Ordering and delivery
Prices include VAT and are per bollard. Lead times vary by finish and fixing. Call 01744 520110 or email sales@industrialsuppliesco.co.uk for lead times, multi-post quantities, delivery to site or help choosing a fixing. We deliver throughout the UK mainland.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

























