-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
If you need to close a car park, service road or yard entrance outside working hours without paying for an automatic barrier, a manual arm barrier is the straightforward answer. This hand-operated, counterweighted barrier lifts with one hand, locks down across the opening when the site is shut and locks up out of the way when traffic needs to flow. It suits facilities and site managers who want controlled access with no power supply or service contract. Choose the drivable width that matches your opening, from 3000mm to 7000mm, and either a cast-in or bolt-down fixing to suit the ground.
Why it works
Counterweighted for one-person operation
The boom pivots on a head mounted on a single pedestal, with a counterweighted tail and grab handle behind the pivot. Because the boom is balanced by the tail, one person can raise and lower it by hand. There is nothing electrical to fail.
Galvanised steel under the colour
The pedestal and head are galvanised mild steel, powder coated red as standard. The galvanising protects the steel where the paint gets chipped, which matters on an exposed entrance. The aluminium boom is light to lift and does not rust.
Lockable in both positions
The barrier can be locked in the lowered position to keep vehicles out, and in the raised position so the boom cannot drop onto traffic during opening hours. The red and white banded boom is easy for drivers to see.
- Hand-operated, counterweighted, no power needed
- Galvanised steel body, aluminium boom
- Lockable raised and lowered; made in the UK
Where it's used
Business park and staff car parks, industrial unit yards, service roads, depots and private access roads: anywhere access only needs restricting at certain times, such as overnight or at weekends, rather than vehicle by vehicle.
Specifications
| Operation | Manual (hand-operated), counterweighted tail with grab handle |
|---|---|
| Drivable width options | 3000mm to 7000mm in 500mm steps |
| Overall height | Approx. 1200mm (1231mm to top of handle on the drawing) |
| Boom height when lowered | Approx. 996mm above ground |
| Tail length behind pedestal | 669mm |
| Overall length | Boom length + 1000mm minimum (includes clearance to pivot) |
| Body material and finish | Galvanised mild steel, powder coated red as standard |
| Boom | Aluminium, red and white bands |
| Boom and post tube sizes | Not published for this line |
| Locking | Lockable in the raised and lowered positions |
| Cast-in fixing | Ragged foot, concreted 600mm below ground; excavated hole no less than 600mm cube |
| Bolt-down fixing | Flanged base plate, four M16 bolts per leg into concrete no less than 600mm cube; bolts not supplied |
| Weight (3m / 4m / 5m / 6m / 7m boom) | Bolt down 48 / 52 / 56 / 69 / 75kg; cast in 46 / 50 / 54 / 67 / 73kg |
| Supplied | Barrier pedestal, counterweighted head and boom. Support post and fixings not included |
| Guarantee | 12 months, if installed and used correctly |
Choosing the right option
Drivable width: measure the clear opening vehicles drive through and choose the width that covers it. The pedestal and tail sit beside the opening, so allow at least the boom length plus 1000mm overall, including clearance to the pivot. One barrier covers up to 7000mm. For wider roads, ask us about a double-span arrangement.
Fixing: choose Cast In (ragged) for new groundworks, soft ground or tarmac. The foot is concreted into an excavated hole 600mm deep. Choose Bolt Down only where there is a sound concrete base of at least 600mm cube to take four M16 anchors. Do not bolt into tarmac, which cannot hold the fixings under the leverage of a long boom.
Accessories: a matching support (catch) post for the end of the boom is available separately. The barrier can also be locked at the catch post using a swing gate barrier locking pin, also sold separately. Red is the standard colour. Call us before ordering if you need a different RAL colour.
Installation, use and care
Set the pedestal so the boom closes square across the opening, with the tail clear of footpaths. For cast-in units, excavate, set the foot plumb and haunch it in concrete, then let it cure fully before using the boom. For bolt-down units, use four M16 anchors per leg suited to your concrete. Put up suitable signs so drivers know the obstruction is there. Check the fixings and pivot periodically and touch up paint damage.
FAQ
Can I bolt it down onto tarmac?
No. The bolt-down version needs a suitable concrete surface of at least 600mm cube. On tarmac, choose the cast-in version and excavate a hole for it, or lay a concrete pad first.
Are the fixing bolts included?
No. The bolt-down version is supplied without fixing-down bolts. You will need four M16 anchors per leg, chosen to suit your concrete. The cast-in version is set in concrete instead.
Does it come with a post for the end of the boom?
No. A matching support or catch post is sold separately.
Can I get it in another colour?
Red powder coat is standard. Other RAL colours can be made to order. Call or email us with the RAL number before you order.
Ordering and delivery
Each barrier is made to order, so check your width and fixing type carefully before ordering. Returns on made-to-order items are restricted. For help with sizing, colours or accessories, call 01744 520110 or email sales@industrialsuppliesco.co.uk.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.



