-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
This heavy-duty galvanised hooped perimeter barrier is made from 101mm diameter, 3mm wall steel tube and built to stop vehicles drifting onto footpaths, forecourts, shop fronts and building entrances. If you manage a car park, showroom, depot or school site and need a permanent line that drivers respect, specify this one. Choose 500, 750 or 1000mm above ground, an overall width of 1000, 1500 or 2000mm, and either a concrete-in or bolt-down fixing to suit the ground you are working with.
Why it works
101mm tube with a 3mm wall
Lighter 48mm or 60mm hoops mark a boundary well but bend easily when a van reverses into them. A 101mm tube gives a far stiffer section and a bigger visual target, so drivers see it in the mirror and it takes knocks that would kink a lighter hoop. It is a deterrent and physical stop for slow-moving vehicles; no impact or crash rating is published for it.
Welded 90-degree elbows
The top rail is joined to each leg with a welded 90-degree elbow rather than a cold bend, which keeps the full tube diameter through the corners and gives the barrier its square-shouldered look. After galvanising, the elbows and straight tube can differ slightly in appearance; that is normal and not a defect.
Galvanised finish
The whole frame is galvanised as standard, so there is no paint to chip and no annual repainting. The zinc coat weathers to a dull silver-grey that suits brick, glass and concrete frontages alike.
- 101mm diameter steel tube, 3mm wall thickness
- Three heights and three widths
- Concrete-in (300mm below ground) or bolt-down flanged legs
- Galvanised finish, no painting needed
Where it's used
Car showroom forecourts, where it protects display vehicles without hiding them; shop and office entrances; bay ends outside glazed frontages; supermarket trolley parks; service yards; school and hospital drop-off zones; and any pedestrian route you need to keep vehicles off.
Specifications
| Tube diameter | 101mm |
|---|---|
| Wall thickness | 3mm |
| Material and finish | Steel tube, galvanised |
| Corners | 90-degree welded elbows |
| Height above ground | 500mm, 750mm or 1000mm |
| Overall width | 1000mm, 1500mm or 2000mm |
| Concrete-in fixing | Legs set 300mm below ground |
| Bolt-down fixing | Welded round flange plate on each leg; 6 bolts per barrier (3 per plate), bolts not included |
| Flange plate size / bolt size | Not published for this line |
| Weight, 500mm high | 19kg (1000 wide), 22kg (1500 wide), 26kg (2000 wide) |
| Weight, 750mm high | 22kg (1000 wide), 26kg (1500 wide), 30kg (2000 wide) |
| Weight, 1000mm high | 26kg (1000 wide), 30kg (1500 wide), 33kg (2000 wide) |
| Guarantee | 12 months when installed and used correctly |
Choosing the right option
Height. 500mm is the usual choice for bay ends and in front of glazing, where you want to stop a bumper without blocking sightlines. 750mm sits at a comfortable leaning height and is easier for drivers to see over a bonnet. 1000mm is the most visible and the one to pick for pedestrian routes, entrances and anywhere people walk close by.
Width. 1000mm suits single doorways, column protection and tight spaces. 1500mm covers a typical parking bay end. 2000mm gives the longest run per barrier and fewer fixings when you are lining a forecourt; leave a gap between barriers if you need pedestrians to pass through.
Fixing. Concrete-in is the strongest and the neatest, with nothing at ground level to trip over or tamper with, but it needs a hole dug and concreted. Bolt-down is the quicker option on an existing sound concrete slab and avoids breaking out the surface; it is not suitable for block paving, tarmac or thin screeds.
Installation, use and care
For concrete-in, excavate a hole for each leg, set the legs 300mm below finished ground level, check the barrier is plumb and square, then backfill with concrete and leave it to cure before any load. For bolt-down, position the barrier on a suitable concrete surface, mark and drill through the three holes in each flange plate and fix with six suitable anchor bolts (supplied separately). The galvanised finish needs only an occasional wash; check fixings after any impact.
Frequently asked questions
Are fixing bolts included with the bolt-down version?
No. Bolt-down barriers need six bolts per barrier, three per flange plate, and these are not included. Choose anchors suitable for your concrete; we can advise if you call us with the slab details.
Can I bolt it down onto block paving or tarmac?
It is designed to be bolted to a suitable concrete surface. On block paving, tarmac or unknown sub-bases, choose the concrete-in version so each leg is set 300mm into its own concrete foundation.
Is it available in colours?
This listing is the standard galvanised finish. Colour coating over galvanising is available as a special order; contact us with the RAL colour and quantity for a price.
Will it stop a car driven at speed?
No impact or crash rating is published for this barrier. Treat it as a heavy-duty deterrent and stop for low-speed manoeuvring, such as parking and reversing, not as a hostile vehicle mitigation product.
Ordering and delivery
Select height, width and fixing above and add to basket. These barriers are made to order and we will confirm the lead time when you order. For multiple barriers, colour coating or site-specific questions, call 01744 520110 or email sales@industrialsuppliesco.co.uk and we will quote promptly.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.



