-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
If you look after a school playground, a park path, a sports ground or a town-centre precinct and need seating that takes years of daily use with almost no upkeep, this backless steel bench is built for that job. The 1800mm seat is made from three square box-section steel slats carried on just two central pedestal posts, so there is no backrest to climb on, no timber to rot and nothing loose to vandalise. People can sit facing either way, which suits open spaces where they look in both directions. It comes in plain galvanised steel or galvanised and powder coated in one of seven RAL colours, and you choose cast-in posts or bolt-down flange plates to suit the ground.
Why it works
Box-section slats that stay straight
Hollow square-section steel is far stiffer than flat bar of the same weight, so the three seat slats span the 1000mm between posts and overhang each end without sagging or flexing when the bench is full. The open ends are closed with plastic end caps, which keep water and litter out of the tubes and leave no sharp edges at knee height.
Two posts, not four legs
Each end of the seat sits on a single round post with a curved saddle bracket underneath, rather than a pair of legs. Fewer contact points mean fewer places for litter to collect, easier sweeping and mowing around the base, and less to fix on a bolt-down install: six bolts per bench in total.
Galvanised steel under every finish
Every version is galvanised mild steel, and the coloured versions are galvanised first and then powder coated. If the coating is chipped, the zinc underneath still protects the steel, which is why this kind of bench needs only minimal maintenance outdoors.
- 1800mm long, 312mm deep, 480mm seat height
- Three box-section slats with plastic end caps
- Two central posts at 1000mm centres
- Supplied fully welded, so there is no assembly on site
Where it's used
Primary and secondary school playgrounds, nursery outdoor areas, parks and country park paths, sports grounds and touchlines, play areas, retail parks, hospital and campus grounds, bus stops and town-centre precincts. The backless design suits narrow paths and the edges of open areas.
Specifications
| Length | 1800mm |
|---|---|
| Depth (seat width) | 312mm |
| Height / seat height | 480mm |
| Seat | Three square box-section steel slats (slat size not published for this line) |
| Supports | Two round steel posts with saddle brackets, 1000mm centres |
| Backrest / armrests | None (backless) |
| Material | Galvanised mild steel |
| Finishes | Galvanised; or galvanised and powder coated RAL 3020 Traffic Red, RAL 9005 Jet Black, RAL 1021 Colza Yellow, RAL 9010 Pure White, RAL 5017 Traffic Blue, RAL 6005 Moss Green or RAL 7001 Silver Grey |
| End caps | Plastic |
| Cast-in fixing | Posts set 300mm below ground in concrete |
| Bolt-down fixing | Round flange plate 133mm x 5mm on each post; 6 x 12mm bolts per bench (bolts not included) |
| Weight | 38kg |
| Construction | Supplied fully welded |
| Seating capacity | Not published for this line |
| Guarantee | 12 months if installed and used correctly |
Choosing the right option
Fixing. Choose Cast In for new paving, grass edges, tarmac or anywhere you can dig: the posts go 300mm into concrete with no plates showing, which gives the neatest finish and the most secure fixing. Choose Bolt Down when the bench is going onto an existing concrete slab or base you don't want to break out. Each post has a round 133mm flange plate, and you need six 12mm bolts suited to the surface.
Finish. Plain galvanised is the lowest-maintenance choice and blends in on most sites. A RAL colour lets you match school or council colours, mark zones in a playground, or make seating easier to see for people with low vision. Yellow and white show grime sooner, while black, green and silver grey hide it best.
Installation, use & care
The bench arrives fully welded. For cast-in, dig two holes at 1000mm centres, set the posts 300mm deep in concrete, check the seat is level and let the concrete cure fully before anyone sits on it. For bolt-down, mark the flange holes on a sound concrete surface and fix with 12mm bolts. Clean off any concrete splashes straight away. After that, wash it down occasionally and check the bolts.
FAQ
Are fixing bolts included?
No. The bolt-down version needs six 12mm bolts per bench, chosen for your surface. Tell us what the base is made of and we can advise.
Can I fit it on grass?
Yes, with the cast-in version. Dig through the turf and set each post 300mm deep in a concrete footing. A bolt-down bench needs a solid concrete base, not soil or slabs on sand.
How many people does it seat?
The manufacturer does not publish a seating capacity for this line. The seat is 1800mm long and people can sit on either side, so allow for that when you plan how many benches you need.
Is a stainless steel version available?
Not in this design. It is made only in galvanised steel or galvanised with a powder-coated RAL colour.
Ordering & delivery
Choose your fixing and finish above and order online. For several benches, delivery to more than one site, or help with fixings, call 01744 520110 or email sales@industrialsuppliesco.co.uk and our team will help with lead times and delivery.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

















