-
Satisfaction Guaranteed.
-
Secure Payments
- Refund policy
-
Need help? Call Us 01744 520 110 or email sales@industrialsuppliesco.co.uk
Description
If you need hard-wearing public seating that people can sit on from either side, this 1800mm backless steel bench is built for the job. Its seat is made from short flat steel slats that run crossways, front to back, along the full length, with the ends turned down at the front and back edges. The whole seat sits on a central spine carried by just two round centre posts, 1000mm apart, so the bench reads as a light, open shape rather than a heavy frame. It is aimed at schools, shopping centres, transport hubs, parks and retail parks, and comes in two seat depths, nine finishes and two fixing methods.
Why it works
Open from both sides
With no backrest and no end frames, people can sit facing either way and step over or around it easily. That suits walkways, atriums and playground edges where a bench needs to serve two directions at once and should not block sight lines.
Two centre posts, plenty of clear floor
Because each leg is a single post under the middle of the seat, the space underneath is mostly clear. Cleaning underneath is quick, and there are no end frames to catch bags or feet. The seat overhangs each post, so the ends feel light without reducing the seating length.
Galvanised or stainless, fully welded
The bench is supplied fully welded, so there is nothing to assemble or tighten on site. The standard finish is hot-dip galvanised mild steel. You can add a powder coat on top of the galvanising in a RAL colour, or choose Grade 304 stainless steel. Galvanised and coated versions have plastic end caps on the open slat ends.
- 1800mm long, 399mm or 589mm deep seat
- Crossways slats with turned-down front and back edges
- Two round centre posts at 1000mm centres
- Cast in (300mm below ground) or bolt down on round 133mm flange plates
- Galvanised, galvanised plus RAL powder coat, or Grade 304 stainless
Where it's used
Typical sites are school playgrounds and dining areas, shopping centre malls and forecourts, bus and rail interchanges, hospital and university grounds, retail parks, town centre schemes and parks. The deeper 589mm seat works well as an island bench in open plazas where people sit on both sides, while the 399mm seat suits narrower paths and against planting.
Specifications
| Length | 1800mm |
|---|---|
| Seat depth (width) | 399mm or 589mm |
| Seat height | 445mm (399mm seat) / 451mm (589mm seat) |
| Post centres | 1000mm |
| Backrest / armrests | None (backless) |
| Material | Mild steel, hot-dip galvanised; or stainless steel Grade 304 |
| Finishes | Galvanised; galvanised + RAL 1021, 3020, 9010, 5017, 9005, 6005 or 7001; brushed stainless steel Grade 304 |
| End caps | Plastic, on galvanised and galvanised and coated versions |
| Cast in fixing | Posts concreted 300mm below ground |
| Bolt down fixing | Round flange plate 133mm x 5mm on each post; 6 x 12mm bolts per bench (not included) |
| Construction | Supplied fully welded |
| Weight | 29kg (399mm seat) / 35kg (589mm seat) |
| Seating capacity | Not published for this line |
| Guarantee | 12 months, if installed and used correctly |
Choosing the right option
Seat depth. The 399mm seat is the standard choice for paths, corridors and spots where people will mostly sit on one side. The 589mm seat is nearly 200mm deeper, so two people can sit back to back comfortably, and it makes a better centrepiece in a plaza or atrium.
Fixing. Choose cast in for new paving, soft landscaping or any site where you are digging anyway; it gives the cleanest look with no visible plates. Choose bolt down for existing concrete slabs, or where you may want to move the bench later. Bolt-down fixings are not included.
Finish. Plain galvanised is the toughest low-maintenance option. A RAL powder coat over the galvanising lets you match school or corporate colours. Grade 304 stainless steel gives a bright metal finish for high-profile schemes; it is not a marine grade, so on exposed coastal sites a galvanised and coated finish is usually the safer choice.
Installation, use and care
For cast in versions, dig a hole for each post, set the bench level at the correct seat height and concrete the posts 300mm below ground. Bolt down versions fix to a suitable concrete surface with 12mm bolts, six per bench. Clean off any concrete splashes straight away and let the concrete cure fully before the bench is used. Wash down occasionally with water and a mild detergent, and touch up any chips in the powder coat to keep the galvanising protected.
FAQ
Are the fixing bolts included with the bolt-down version?
No. Bolt-down benches need six 12mm bolts suited to your concrete base, and these are not supplied. Most installers use anchors or resin studs chosen for the slab they are fixing into.
Does the bench arrive flat-packed?
No. It is supplied fully welded, so the only site work is excavating and concreting (cast in) or drilling and bolting (bolt down).
Can I order a RAL colour that is not listed?
The listed colours are the ones we can price online. If you need a different RAL colour, call or email us before ordering and we will confirm availability and price.
Ordering and delivery
Prices shown include VAT. Lead times vary by finish. For current lead times, delivery to your site, bulk quantities or a formal quotation, call 01744 520110 or email sales@industrialsuppliesco.co.uk.
Our products have been used by
Logos are for illustrative purposes only and do not imply official endorsement
About Us
Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.





































