Heavy Duty Garage Floor Paint High Impact Paint For Car Truck Forklift And Racking Floor Paint By Industrial Supplies


Price:
Sale price£98.35
Inc. Vat

Express Shipping On All Orders

Our Clients

Description

Heavy Duty Garage Floor Paint High Impact Paint For Car Truck Forklift And Racking Floor Paint
Heavy Duty floor paint for coating industrial floors showrooms, garages and factory floors.
This coating is Ideal for use on concrete, stone, wood, metal surfaces but not power floated, screed or bituminous floors and will withstand most forms of traffic including plant and fork trucks. Our garage floor paint is designed to provide very good abrasion resistance with a long lasting high build finish and high industrial strength.
Factory floor paint exhibits the highest strength whilst offering smooth, attractive Semi gloss finish. Our garage floor paint is high build coating that produces a truely stunning finish for areas such as showrooms where you need to impress
The functions of the industrial floor paint are:
1. To strengthen and improve the factory floor surface
2. To eliminate dust build up on surface (pre seal primer coating is always advised on dusty unpainted areas before a topcoat is applied)
3. To increase the floors abrasion and wear resistance
4. To provide the increased additional chemical resistance
5. To improve the appearance and ambience of the working environment
6. To speed up the cleaning/mopping of the area cutting down on time of this task and also to help combat dust issues on stock and surface contamination
7. To delineate specific areas, such as: safe walking areas, parking bays or access routes and other directions etc.

This coating is Ideal for use on concrete, stone, wood, metal surfaces but not power floated, screed or bituminous floors and will withstand most forms of traffic including plant and fork trucks. However any new concrete base / floor must be more than 16 weeks old before painting and our Underguard floor seal would be recommended prior to painting with topcoat.

200m squared per 2,100ft squared per 20litre tub (as listed)

(Two Coats Always Advised)

Dry time of coating using standard roller in areas with minimal air moisture (lab conditions)

touch dry @ 15'c = 10/12 hours

in winter months please allow extra time for curing,5% white spirits can be added to the product in winter months to help with these sub 15'c temperatures and help combat slow drying times, when coating in these months please still open as many windows and doors possible to create a natural air flow over the coated area a space heater can also be added, do not trap warm air as this will also keep the coating soft as it is a polyurethane product.

do not apply over water, oil or grease any contamination will have to be dealt with before coating of that area get in contact for tips and advise via the message tab on this site.

first coat should be left to dry for 24 hours to assure adhesion to surface leave minimum of 24 hours for after coats always leaving minimum of 48 hours before 100% use of area again

true 100% cure will only be 7 days after application  of last coating

applying multi thin coats is advised and not thick coats. (as thick coatings will surface dry and the under layer will remain soft)

work in a well ventilated area,using no forms of naked light/fire

please test for damp before coating by applying a small test patch or applying a clear plastic sheet (30cmx30cm) and sealing it to the floor with a high grade tape (duck tape) with out any ways of air escaping and leave for 24 hours if there is any forms of water vapour on the sheet the are will have damp and steps will need to be taken before coatings

Mix very well before use  using a drill/paddle tool

If the area you are looking to coat is virgin (never been coated) or has had contamination from oil,grease,cutting agents etc,Cleaning with correct equipment/surface preparation products will be required.

quick tip: on virgin surfaces or areas with adhesion issues with past coatings apply a small amount of water to the bare concrete if the water beads on the top the surface will need acid etching or abrading if the water soaks in then it will be fine to start steps towards coating.

The area will then need to be coated with a heavy duty pre seal and left to dry for 24 hours (you can purchase this pre seal on the drop down menu) do not use pva as this is only a wood glue and not a stable layer for industrial coatings to adhere to.

Powerfloated/Screed areas (smooth shinny concrete) will need to be treated with a acid etch or abrade by mecanical means all product info will be displayed on the item you will take collection of product safety data sheets can be requested on all our range.

a test patch is always advised as some areas my still have contamination and this could have complications when coating 

product weight 20kg minimum our delivery service will bring the product to your door saving you any issues with moving heavy items from there vehicle.


About Us

Suppliers to Ministry of Defence, NATO, US Airforce and Most UK Councils, Schools, Universities, Hospitals & various Government departments

Payment & Security

American Express Apple Pay Diners Club Discover Google Pay Klarna Maestro Mastercard Shop Pay Union Pay Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

You may also like

Recently viewed