{"product_id":"double-bearing-gate-wheel-weld-on-plates-100mm-v-groove","title":"Double Bearing Gate Wheel with Weld-On Plates 100mm, V Groove","description":"\u003cp\u003e\u003cstrong\u003eA 100mm wheel with weld-on side plates, for a sliding gate running on V section ground track.\u003c\/strong\u003e The wheel is 98mm measured and runs on a double bearing, with a V shaped groove 20mm across and a rim 25mm wide. Two pressed steel plates hold it, and each plate turns out into a foot flange at its base, so you weld the flanges to your gate's bottom rail and do not need an axle bolt. The flanges have no bolt holes, so this is a weld-on fitting. On the data sheet the running edge stands 18mm below the flanges, which is what sets the gap under your gate. No load rating is published for this wheel. The price shown is for one wheel, with a minimum order of 6.\u003c\/p\u003e\n\u003cfigure style=\"margin:16px 0\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0621\/3002\/8778\/files\/double-bearing-gate-wheel-weld-on-plates-100mm-v-groove-drawing.jpg?width=1200\" alt=\"Drawing of the 100mm double bearing V groove gate wheel with weld-on plates, showing the published dimensions\" width=\"1200\" height=\"1200\" loading=\"lazy\" style=\"display:block;width:100%;max-width:760px;height:auto;margin:0 auto\"\u003e\u003c\/figure\u003e\n\u003ch2\u003eWhy this wheel works\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eV groove in a weld-on housing.\u003c\/strong\u003e The wheel is 98mm measured with a 25mm rim, held between two plates. The base flanges measure 52mm across overall, so check that against the width of your rail.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeld once and leave it.\u003c\/strong\u003e With the plates welded to the rail, there is no axle bolt to come loose, and the wheel holds its position in the frame.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe groove holds the line.\u003c\/strong\u003e The V shaped groove keeps the wheel on the track, so the gate runs straight and does not wander off the V.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTwo bearings on the axle.\u003c\/strong\u003e The double bearing shares the load between two bearings rather than one.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePlated against rust.\u003c\/strong\u003e The wheel and plates are yellow zinc plated, not hot-dip galvanised, so paint the welds after fitting.\u003c\/p\u003e\n\u003ch2\u003eWhere it is used\u003c\/h2\u003e\n\u003cp\u003eSliding gates on V section ground track where you are welding the wheel into the bottom rail rather than bolting it on, on new gates in a fabrication shop or when replacing a wheel unit of the same size.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eWhat you get\u003c\/th\u003e\n\u003ctd\u003eOne wheel with weld-on plates, minimum order 6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWheel diameter\u003c\/th\u003e\n\u003ctd\u003eSold as 100mm, 98mm measured on the data sheet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGroove\u003c\/th\u003e\n\u003ctd\u003eV groove, 20mm across\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTrack\u003c\/th\u003e\n\u003ctd\u003eV section ground track\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRim width overall\u003c\/th\u003e\n\u003ctd\u003e25mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth over the side plates\u003c\/th\u003e\n\u003ctd\u003e38mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeight of the plates\u003c\/th\u003e\n\u003ctd\u003e65mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth over the base flanges\u003c\/th\u003e\n\u003ctd\u003e52mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePlate thickness\u003c\/th\u003e\n\u003ctd\u003e2.5mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWheel stands below the flanges\u003c\/th\u003e\n\u003ctd\u003e18mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFixing\u003c\/th\u003e\n\u003ctd\u003eWeld-on, flanges have no bolt holes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBearing\u003c\/th\u003e\n\u003ctd\u003eDouble bearing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eYellow zinc plated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum load\u003c\/th\u003e\n\u003ctd\u003eNot published for this line\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003eAbout 1.48 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eChoosing the right option\u003c\/h2\u003e\n\u003cp\u003eChoose the groove first, because it must match your track. Then the fixing, then the diameter: a larger wheel rolls over grit more easily but needs more room under the rail.\u003c\/p\u003e\n\u003cp\u003eThis is the V groove version of the weld-on wheel. The 100mm round groove wheel with plates has the same 98mm size, plates and 38mm width, and differs only in the groove, so buy the one that matches your track. If you would rather bolt the wheel through a bracket, the 100mm double bearing V wheel with an M14 axle does the same job on the same track.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eOption\u003c\/th\u003e\n\u003cth\u003eHow it differs\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e100mm double bearing V groove with weld-on plates\u003c\/td\u003e\n\u003ctd\u003eThis wheel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/double-bearing-sliding-gate-wheel-100mm-v-groove-m14-axle\"\u003e100mm double bearing V groove wheel, M14 axle\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eThrough bolt, no plates\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/100mm-diameter-slider-wheel\"\u003e100mm V groove wheel, bolt-through axle\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eV track, no double bearing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/premium-3m-ground-track-for-v-wheels\"\u003eV section ground track, 3m galvanised\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eThe ground track for V groove wheels\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch2\u003eFitting and care\u003c\/h2\u003e\n\u003cp\u003eLay the track first, straight and level. Most sliding gates run on two wheels, set about a fifth of the gate length in from each end. Weld the flanges to the underside of your bottom rail, with the plates and the top of the wheel up inside an open-bottomed channel or a slot cut in the rail. On the data sheet the running edge stands 18mm below the flanges, so measure your gap from there. Tack first, check the gate runs true along the full length, then weld in short runs to keep heat away from the bearings.\u003c\/p\u003e\n\u003cp\u003eKeep grit and leaves off the track, because that is what wears a wheel. Paint the welds, and check the wheels run freely at each service.\u003c\/p\u003e\n\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\n\u003cdetails\u003e\u003csummary\u003eIs the price for one wheel?\u003c\/summary\u003e\u003cp\u003eYes, the price is for one wheel, and the minimum order is 6. Most sliding gates run on two wheels. For a larger job, call us and we will confirm availability before you order.\u003c\/p\u003e\u003c\/details\u003e\n\u003cdetails\u003e\u003csummary\u003eWhat track does it run on?\u003c\/summary\u003e\u003cp\u003eV section ground track. The groove measures 20mm across on the data sheet. It will not run on a round bar track.\u003c\/p\u003e\u003c\/details\u003e\n\u003cdetails\u003e\u003csummary\u003eDoes it bolt or weld?\u003c\/summary\u003e\u003cp\u003eWeld. The base flanges have no bolt holes, so they are welded to the gate's bottom rail. If you want to bolt a wheel on, look at the bolt-through V wheel with an M14 axle in the table.\u003c\/p\u003e\u003c\/details\u003e\n\u003ch2\u003eOrdering and delivery\u003c\/h2\u003e\n\u003cp\u003eOrder 6 or more online, with Express UK Delivery to your site and same-day dispatch on orders before 2pm, Monday to Friday. For a larger job, call 01744 520 110 or email sales@industrialsuppliesco.co.uk and we will confirm availability and delivery before you order.\u003c\/p\u003e\n","brand":"Industrial Supplies Co","offers":[{"title":"Default Title","offer_id":63254462660995,"sku":"SSHF-874243-01","price":16.9,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0621\/3002\/8778\/files\/double-bearing-gate-wheel-weld-on-plates-100mm-v-groove-in-use.jpg?v=1794145677","url":"https:\/\/industrialsuppliesco.co.uk\/products\/double-bearing-gate-wheel-weld-on-plates-100mm-v-groove","provider":"industrialsuppliesco.co.uk","version":"1.0","type":"link"}